|
AIR-AP4800-E-K9C Specification
|
|
Description
|
802.11ac W2 Analytics AP w/CA; 4×3:3; Location; mGig -E Domain, Configurable
|
|
Software and supported wireless LAN controllers
|
● Cisco Unified Wireless Network Software Release 8.7 or later
● Cisco 3500 Series Wireless Controllers, 5520 Series Wireless Controllers, 8540 Series Wireless Controllers, and Virtual Wireless Controller, Cisco 9800 series Wireless Controllers
● Cisco IOS ® XE Software Release 16.9
● Cisco Catalyst ® 3850 Series and 3650 Series Switches
|
|
802.11n version 2.0 (and related) capabilities
|
● 4x4 MIMO with three spatial streams
● Maximal Ratio Combining (MRC)
● 802.11n and 802.11a/g beamforming
● 20- and 40-MHz channels
● PHY data rates up to 450 Mbps (40 MHz with 5 GHz)
● Packet aggregation: A-MPDU (Tx/Rx), A-MSDU (Tx/Rx)
● 802.11 Dynamic Frequency Selection (DFS)
● Cyclic Shift Diversity (CSD) support
|
|
802.11ac Wave 1 capabilities
|
● 4x4 MIMO with three spatial streams
● MRC
● 802.11ac beamforming
● 20-, 40-, and 80-MHz channels
● PHY data rates up to 1.3 Gbps (80 MHz in 5 GHz)
● Packet aggregation: A-MPDU (Tx/Rx), A-MSDU (Tx/Rx)
● 802.11 DFS
● CSD support
|
|
802.11ac Wave 2 capabilities
|
● 4x4 MU-MIMO with three spatial streams
● MRC
● 802.11ac beamforming
● 20-, 40-, 80, 160-MHz channels
● PHY data rates up to 5.2 Gbps
● Packet aggregation: A-MPDU (Tx/Rx), A-MSDU (Tx/Rx)
● 802.11 DFS
● CSD support
|
|
Wi-Fi Alliance certifications
|
● Wi-Fi Certified a, b, g, n, ac
● Wi-Fi Vantage
● Wi-Fi Multimedia (WMM)
● Passpoint
|
|
Integrated antenna
|
Flexible radio (either 2.4 GHz or 5 GHz)
● 2.4 GHz, gain 2.5 dBi, internal antenna, omnidirectional in azimuth
● 5 GHz, gain 5 dBi, internal directional antenna, elevation plane beam width 90°
Dedicated 5-GHz radio
● 5 GHz, gain 3.5 dBi, internal antenna, omnidirectional in azimuth
Third dedicated radio
● 2.4 GHz and 5 GHz capable
● Hyperlocation antenna array
BLE radio
● 2.4 GHz, gain 2.5 dBi, internal antenna, omnidirectional in azimuth
|
|
Interfaces
|
● 2 Ethernet ports
● 100/1000/2500/5000 Multigigabit Ethernet (RJ-45) – IEEE 802.3bz
● Category 5e cabling
● Higher-quality 10GBASE-T (Category 6/6a) cabling
● 100/1000BASE-T autosensing (RJ-45 AUX port)
● Management console port (RJ-45)
|
|
Indicators
|
● Status LED indicates boot loader status, association status, operating status, boot loader warnings, boot loader errors
|
|
Dimensions (W x L x H)
|
● Access point (without mounting brackets): 8.68 x 9.9 x 2.9 in. (22 x 25 x 7.35 cm)
|
|
Weight
|
● 5.6 lb (2.5 kg)
|
|
Input power requirements
|
● 802.3at PoE+, Cisco Universal Power over Ethernet (Cisco UPOE ®)
● 802.3at power injector (AIR-PWRINJ6=)
● 50W power supply (AIR-PWR-50=)
|
|
Power draw
|
● 30W at the Power Source Equipment (PSE) with all features enabled except Multigigabit, AUX Ethernet, and USB support
● 31W at the PSE with full functionality
|
|
Environmental
|
● Nonoperating (storage) temperature: -22° to 158°F (-30° to 70°C)
● Nonoperating (storage) altitude test: 25˚C, 15,000 ft
● Operating temperature: 32° to 104°F (0° to 40°C)
● Operating humidity: 10% to 90% percent (noncondensing)
● Operating altitude test: 40˚C, 9843 ft. (noncondensing)
|
|
System memory
|
● 1024 MB DRAM
● 256 MB flash
|
|
Available transmit power settings
|
2.4 GHz
● 23 dBm (200 mW)
● 20 dBm (100 mW)
● 17 dBm (50 mW)
● 14 dBm (25 mW)
● 11 dBm (12.5 mW)
● 8 dBm (6.25 mW)
● 5 dBm (3.13 mW)
● 2 dBm (1.56 mW)
5 GHz
● 23 dBm (200 mW)
● 20 dBm (100 mW)
● 17 dBm (50 mW)
● 14 dBm (25 mW)
● 11 dBm (12.5 mW)
● 8 dBm (6.25 mW)
● 5 dBm (3.13 mW)
● 2 dBm (1.56 mW)
|
|
|
Frequency band and 20-MHz operating channels
|
E (E regulatory domain):
● 2.412 to 2.472 GHz; 13 channels
● 5.180 to 5.320 GHz; 8 channels
● 5.500 to 5.700 GHz; 8 channels
(excludes 5.600 to 5.640 GHz)
|
|
