Точки доступу Aruba (HPE) забезпечують швидку та стабільну бездротову передачу даних у корпоративній мережі. Aruba пропонує як прості пристрої для надання базового функціоналу мережі Wi-Fi, так і для мереж із високою щільністю користувачів та швидкостями до 2 Гбіт/с, а також захищені моделі для роботи у складних кліматичних умовах.
Точки доступу прості в інсталяції, можуть працювати одночасно в діапазонах 2,4 і 5 ГГц, використовують технологію MIMO для збільшення швидкості передачі даних та підтримують стандарт 802.11ac Wave2.
Instant-точки доступу Aruba — не вимагають окремого контролера, а використовують віртуальний контролер, функції якого виконує одна з точок. HPE Aruba Instant — це рішення, яке дозволяє розгорнути «безконтрольну» мережа WiFi корпоративного рівня. У нього вже вбудована мережна безпека, автоматичне керування RF та достатньо інтелектуальних функцій для запуску повноцінного рішення без додаткового ліцензування. Керується кластер із точок доступу за допомогою віртуального контролера, який розміщується на одній із точок доступу (IAP). Контролер відповідає за процес автоконфігурування нових точок доступу, авторизацію та автентифікацію, гостьовий доступ та мережеві сервіси (NAT, DHCP та ін.).
Технічні характеристики точки доступу Aruba (HPE) JW184A:
|
AP-320 SERIES SPECIFICATIONS
|
- AP-325 and IAP-325
- 5 GHz (1,733 Mbps max rate) and 2.4 GHz (600 Mbps max rate) radios, each with 4x4 MIMO support and a total of eight integrated omni-directional downtilt antennas.
- AP-324 and IAP-324
- 5 GHz (1,733 Mbps max rate) and 2.4 GHz (600 Mbps max rate) radios, each with 4x4 MIMO support and a total of four combined, diplexed (dual-band) external RP-SMA antenna connectors.
|
|
WIRELESS RADIO SPECIFICATIONS
|
- AP type: Indoor, dual radio, 5 GHz 802.11ac and 2.4 GHz 802.11n 4x4 MIMO.
- Software-configurable dual radio supports 5 GHz (Radio 0) and 2.4 GHz (Radio 1).
- Four spatial stream SU-MIMO for up to 1,733 Mbps wireless data rate to a single client device.
- Three spatial stream MU-MIMO for up to 1,300 Mbps wireless data rate to up to three MU-MIMO capable client devices simultaneously.
- Support for up to 256 associated client devices per radio, and up to 16 BSSIDs per radio.
- Supported frequency bands (country-specific restrictions apply):Available channels: Dependent on configured regulatory domain.
- 2.400 to 2.4835 GHz
- 5.150 to 5.250 GHz
- 5.250 to 5.350 GHz
- 5.470 to 5.725 GHz
- 5.725 to 5.850 GHz
- Dynamic frequency selection (DFS) optimizes the use of available RF spectrum.
- Supported radio technologies:
- 802.11b: Direct-sequence spread-spectrum (DSSS)
- 802.11a/g/n/ac: Orthogonal frequency-division multiplexing (OFDM)
- Supported modulation types:Transmit power: Configurable in increments of 0.5 dBm
- 802.11b: BPSK, QPSK, CCK
- 802.11a/g/n/ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM
- Maximum (aggregate, conducted total) transmit power (limited by local regulatory requirements):Advanced Cellular Coexistence (ACC) minimizes interference from cellular networks.
- 2.4 GHz band: +24 dBm (18 dBm per chain)
- 5 GHz band: +24 dBm (18 dBm per chain)
- Note: conducted transmit power levels exclude antenna gain. For total (EIRP) transmit power, add antenna gain
- Maximum ratio combining (MRC) for improved receiver performance.
- Cyclic delay/shift diversity (CDD/CSD) for improved downlink RF performance.
- Short guard interval for 20-MHz, 40-MHz and 80-MHz channels.
- Space-time block coding (STBC) for increased range and improved reception.
- Low-density parity check (LDPC) for high-efficiency error correction and increased throughput.
- Transmit beamforming (TxBF) for increased signal reliability and range.
- Supported data rates (Mbps):802.11n high-throughput (HT) support: HT 20/40
- 802.11b: 1, 2, 5.5, 11
- 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
- 802.11n: 6.5 to 450 (MCS0 to MCS23)
- 802.11ac: 6.5 to 1,733 (MCS0 to MCS9, NSS = 1 to 4)
- 802.11ac very high throughput (VHT) support: VHT 20/40/80
- 802.11n/ac packet aggregation: A-MPDU, A-MSDU
|
|
POWER
|
- Maximum (worst-case) power consumption: 20W (802.3at PoE), 13.5W (802.3af PoE) or 18.5W (DC)Maximum (worst-case) power consumption in idle mode: 8W (PoE) or 7W (DC).
- Excludes power consumed by external USB device (and internal overhead); this could add up to 6W (POE) or 5.5W (DC) for 5W/1A USB device
- Direct DC source: 48Vdc nominal, +/- 5%.
- Power over Ethernet (PoE): 12 Vdc (nominal) 802.3af/802.3at compliant sourceUSB port disabled
- Unrestricted functionality with 802.3at PoE
- Power-save mode with reduced functionality from 802.3af PoE
- Second Ethernet port disabled
- 2.4 GHz radio in 1x1:1 mode
- Power sources sold separately
- When both power sources are available, DC power takes priority
|
|
WI-FI ANTENNAS
|
- AP-324/IAP-324:
- Four RP-SMA connectors for external dual band antennas. Internal loss between radio interface and external antenna connectors (due to diplexing circuitry): 2.5 dB in 2.4 GHz and 1.5 dB in 5 GHz.
- AP-325/IAP-325:
- Eight integrated downtilt omni-directional antennas for 4x4 MIMO with maximum antenna gain of 4.0 dBi in 2.4 GHz and 4.7 dBi in 5 GHz. Built-in antennas are optimized for horizontal ceiling-mounted orientation of the AP. The downtilt angle for maximum gain is ~ 30 degrees. Combining the patterns of each of the antennas of the MIMO radios, the peak gain of the effective per-antenna pattern is 2.7 dBi in 2.4GHz and 2.9 dBi in 5GHz.
|
|
OTHER INTERFACES
|
- Two 10/100/1000BASE-T Ethernet network interfaces (RJ-45)DC power interface, accepts 2.1/5.5-mm center-positive circular plug with 9.5-mm length
- Auto-sensing link speed and MDI/MDX
- Load balancing support to achieve platform throughput greater than 1 Gbps
- 802.3az Energy Efficient Ethernet (EEE)
- PoE-PD: 48 Vdc (nominal) 802.3af or 802.3at PoE
- USB 2.0 host interface (Type A connector)
- Bluetooth Low Energy (BLE) radioVisual indicators (tri-color LEDs): For system and radio status
- Up to 4dBm transmit power (class 2) and -94dBm receive sensitivity
- Integrated antenna, -5dBi gain (30 degree downtilt)
- Can be disabled with configuration
- Reset button: Factory reset (during device power up)
- Serial console interface (RJ-45)
- Kensington security slot
|
|
MOUNTING
|
- The AP ships with two (white) mounting clips to attach to a 9/16-inch or 15/16-inch flat T-bar drop-tile ceiling.
- Several optional mount kits are available to attach the AP to a variety of surfaces; see the Ordering Information section below for details
|
|
MECHANICAL
|
- Dimensions/weight (unit, excluding mount accessories):
- 203 mm (W) x 203 mm (D) x 57 mm (H), 8.0” (W) x 8.0” (D) x 2.2” (H)
- 950 g/34 oz
- Dimensions/weight (shipping):
- 315 mm (W) x 265 mm (D) x 100 mm (H), 12.4” (W) x 10.4” (D) x 3.9” (H)
- 1,350 g/48 oz
|
|
ENVIRONMENTAL
|
- Operating:
- Temperature: 0° C to +50° C (+32° F to +122° F)
- Humidity: 5% to 93% non-condensing
- Storage and transportation:
- Temperature: -40° C to +70° C (-40° F to +158° F)
|
|
REGULATORY
|
- FCC/Industry of Canada
- CE Marked
- R&TTE Directive 1995/5/EC
- Low Voltage Directive 72/23/EEC
- EN 300 328
- EN 301 489
- EN 301 893
- UL/IEC/EN 60950
- EN 60601-1-1 and EN 60601-1-2
For more country-specific regulatory information and approvals, please see your Aruba representative.
|
|
RELIABILITY
|
|
MTBF: 739,935 hrs (84.5yrs) at +25C operating temperature (AP-325)
|
|
REGULATORY MODEL NUMBERS
|
- AP-324 and IAP-324: APIN0324
- AP-325 and IAP-325: APIN0325
|
|
CERTIFICATIONS
|
- CB Scheme Safety, cTUVus
- UL2043 plenum rating
- Wi-Fi Alliance (WFA) certified 802.11a/b/g/n/ac
- Bluetooth SIG interoperability certification
- Passpoint® (Release 2) with ArubaOS and Instant 8.3+
|
|
WARRANTY
|
|
Aruba limited lifetime warranty
|
|
MINIMUM SOFTWARE VERSIONS
|
- ArubaOS 6.4.4.0
320 Series Access Points are not supported on 650 Series Mobility Controllers.
- Aruba InstantOS 4.2.1.0
|
